Flipped the power on/off
Flipped the circuit breaker on /off
Tried getting the pump working by manually spinning the blade.
All to no avail.
So I called the pool repair people. About a week or 2 after my call, they finally showed up. They turned the switch on and the Polaris pump started right up - no problem. They couldn't explain why it wasn't working. All they could tell me was that an $80 service call bill would be coming.
The Polaris pump worked for a month or so and then stopped working again. I went through all the same things as mentioned above but it still wouldn't work.
I decided that since the pump was maybe 3 years old that it was probably bad. (The pool repair people also had said that these pool pumps generally have a life of 3 years or so.)
My next decision was: should I order one and replace it myself, or, pay to have it done. I looked at the Polaris pump and all it had was power coming in and 2 high pressure hoses attached to it. This meant that all I should have to do would be to connect 3 wires (and the ground) and the 2 hoses.
I figured I could handle this myself. I would disconnect the old wiring - noting where everything was, and then re-connect them on the new pump. Worst case, I would have to get a friend who could do electrical work if I had a problem.
I searched on the Internet for a pump. There were a lot of places that sold them. Luckily one of the links that came up was one of those price comparison sites. They had www.PoolSupplyWorld.com listed as the cheapest and also had free shipping. Wow!
Next question - what about those high pressure hoses? Do I have to change them? How do those connections work?
Well, I decided I would worry about that later. I figured that worst case I would have to go to the local hardware store and buy new ones.
I placed my order and within a day or two the order was shipped. So, in less than a week I had my parts and was ready to go.
Upon receiving the pump, I opened it up to make sure that it was identical to the one I had. It was. To my surprise it also came with a new high pressure hose and new fittings. Wow again!!
Time to install the new pump - This really wasn't that bad.
First, before beginning, the safest thing is to turn off the power to the pool at the circuit breaker.
Then, as I noted above, I just made sure I understood where the wires were on the old pump and put them on the new pump. Since the pumps were identical, this was pretty straight forward.
As for the high pressure hoses, I didn't know if I should change them (and the fittings) or re-use the ones I had on. I decided I would re-use the ones that were on. If they wouldn't seal up properly, then I would put the new ones on. I attached the hoses (using clear silicone caulk on the threads as they recommend). No leaks.
Time to turn the pump on and admire my work.
Turned the pump on and nothing happened. It acted just like the old pump. I was sure I had everything wired properly so it had to be something else.
Now I am not an electrician, but I got out my voltmeter and started checking the voltage to see where I had voltage and where I didn't. I found that I had power coming to the timer boxer, where the Polaris on/off timer was, but I didn't have any power on the lines going to the pump.
I found the timer switch that turns the pump on and off. It is a big brass switch. Turns out that I had power on one side of the switch, and no matter what I did, there was no power on the other side of the switch.
I then started to notice that there were a whole bunch of dead ants in the vicinity of the switch, so I cleaned them out real good and made sure the switch made good contact with itself. I flipped the Polaris pump switch one more time and the pump came on.
Turns out that sometimes I get ants up in the timer controls. I don't know if they go up them for warmth or what, but I have noticed them up there in the past.
What must have happened is that a bunch of ants went up there and got 'fried'. There must have been just enough of them to block the switch and prevent it from making good electrical contact for when they were cleaned out, everything was fine again.
So the moral of the story is - if a pump or something doesn't work, don't assume the pump (or whatever) is bad.
In this case I should have started with the voltmeter and followed the power flow right from the beginning. I would have found that there was no power on the other side of the switch and would have realized then and there that the pump was probably okay and the problem lay with the switch.
If I would have done this I would have saved myself a few hundred dollars and would have had a working pool much sooner.
I can take pride in the fact that I did change things myself, saving me hundreds of dollars, and that I now have a backup pump if I ever need one.
What I am curious about though is if I would have called the pool repair people and let them do the work for me, would they have been honest with me and told me that the switch was dirty, or, would they have put on a new pump, charged me exorbitantly and never mention the fact that the real problem was in the switch.
I guess I will never know.
No comments:
Post a Comment